Can PP-PE Co‑extruded Sheet Deliver Low‑Cost, Leak‑Proof Blister Packs For Chilled Food?
2026-11-20
PP-PE Co extruded Sheet: LowCost, Direct HeatSealable Blister Boxes for Refrigerated Food
CASE STUDY | Food Packaging Material Selection
Finding one packaging material that checks three boxes — low unitcost, direct heatsealing capability and reliable refrigeration performance — is surprisingly challenging. Budgetfriendly materials often deliver weak seals, while highperformance sealing solutions drive up costs significantly. Our winning solution: blister forming with PPPE coextruded sheet. PP provides structural rigidity and good thermoformability; the integrated PE layer serves as the sealing interface, enabling direct heatsealing with PE lidding film.
This case study breaks down how the sheet satisfies all three hard requirements, its additional value adding benefits, and frequently asked practical questions from packaging buyers.
Defeng — Sheet & Blister Packaging Solutions
![]()
![]()
Project Snapshot
|
Item |
Details |
|
Customer Profile |
Food manufacturer; blister boxes for primary food packaging, sealed with PE lidding film |
|
Three Mandatory Requirements |
Low perunit cost • Direct heatsealable rim • Suitable for refrigerated storage |
|
Why conventional materials fall short |
Singlelayer PP yields poor seal strength; APET needs extra lamination / coating for heatsealing; PVC faces cost & compliance risks |
|
Defeng Solution |
Thermoformed PPPE coextruded sheet; PE inner layer directly heatfused to PE lidding film |
|
Available Specifications |
Thickness: 0.17-2.0 mm,Max sheet width:1000 mm;Customizable PE layer thickness ratio |
Customer feedback in plain terms: Keep packaging costs under control, prevent leakage, and make sure packs survive coldroom storage. Balancing low cost against reliable sealing creates the core materialselection challenge.
![]()
How the 3 Core Requirements Are Met
1. Cost efficiency: Savings from low density & simplified workflows
PP has a density of ~0.91 g/cm³, roughly 30% lighter than PET (~1.33 g/cm³). For identical thickness and footprint, material cost per finished box is substantially reduced. Multi-layer co-extrusion is completed during sheet manufacturing. Thermoformers receive ready to process sheet for forming and sealing, removing secondary lamination or coating steps. Process level savings directly lower unit box cost.
2. Reliable heatsealing: Sealing layer builtin, no posttreatment
The PE co-extruded layer on the tray rim fuses with PE lidding film. Both are polyolefin materials; polymer chains inter-diffuse and bond permanently upon heating, instead of simple surface adhesion from glue. Wide operating tolerance for temperature and pressure delivers consistent seal strength, achieving air-tight and leak-proof performance. Standard heat-sealing machines work perfectly; no high-frequency welder or surface pre-treatment required.
3. Refrigerationready: Stable performance at 04 °C
PP brittlement threshold sits close to 0 °C. Standard grades perform reliably under typical refrigerated conditions (0-4 °C) without cold-cracking risk. Polyolefin absorbs almost no moisture, so trays will not soften or deform in high-humidity cold-storage environments. This is why PP-PE co-extruded sheets are widely adopted for refrigerated food inserts.
Important note: For deepfreeze applications below 18 °C, special lowtemperature copolymer formulation plus colddrop testing is mandatory, which counts as a separate specification scope.
Additional Bonus Benefits Delivered
✅ Adhesivefree sealing, simpler foodcontact compliance Glued seals require thorough evaluation for solvent residue and substance migration — critical risks for food grade packaging. PE to PE fusion sealing adds no foreign materials at the seal joint. Packaging composition stays transparent and easy to document for food-contact certification.
✅ All-polyolefin construction supports circular-economy requirements Both blister tray (PP+PE) and lidding film (PE) belong to the polyolefin family. Compared with multi-material hybrid packaging, sorting and recycling become much easier. This brings tangible advantages during end-customer sustainability audits and aligns with EU PPWR regulatory requirements.
✅ Heat-resistant PP base for multi-purpose production PP long-term service temperature exceeds 100 °C. It out-performs PVC / PS for hot fill and secondary high temperature processing. One sheet grade can cover both refrigerated and heat-resistant use cases, reducing material change-overs on your production line.
Need custom PP-PE co-extruded sheet for your chilledfood blister project? Contact Defeng’s technical team for datasheets and solutions provider.
